How To Clean Bissell Revolution Pet Pro: Step-By-Step Guide

Unplug, empty tanks, rinse parts, clear pet hair, air-dry, then reassemble.

If you want to master how to clean bissell revolution pet pro, you’re in the right place. I service and use these machines weekly, and I’ll show you a simple, proven routine that keeps suction strong, smells fresh, and parts clog-free. Stick with me and learn expert steps, real fixes, and smart care that extend the life of your BISSELL.

What you need to clean your BISSELL Revolution Pet Pro

Gather your tools first. This keeps the job fast and neat.

Warm water and a few drops of mild dish soap Use this to wash removable parts.
Microfiber cloths and paper towels Wipe, polish, and dry edges.
Soft brush or old toothbrush Scrub grooves and seals.
Bottle brush or small sponge Reach into tanks and hose ends.
Tweezers or a seam ripper Lift trapped hair from brush rolls.
Cotton swabs Clean tight corners and the CleanShot area.
Optional: compressed air Blow out fine lint in dry areas only.

Tip from the bench: A labeled bin for machine parts helps you track screws and covers. If you are learning how to clean bissell revolution pet pro, this one habit avoids lost parts and reassembly stress.

Safety first: prep before you start

Always unplug the machine. Let it cool for a few minutes after use. Remove the clean and dirty water tanks. Press the trigger a few times to release any leftover pressure.

Work over a tub or a large sink. Keep the motor housing away from water. Snap a few photos as you go. They help when you put parts back. This safety prep is step one in how to clean bissell revolution pet pro without damage.

Step-by-step: after-each-use cleaning

Do this quick clean after every job. It takes 10 minutes and prevents clogs.

Empty and rinse the dirty water tank Rinse the tank, lid, and float stack until clear. Shake out excess water.
Rinse the nozzle cover and brush roll cover Pop them off. Rinse under warm water until the channels run clear.
Remove hair from brush rolls Pull hair by hand. Use a seam ripper for tight wraps at the end caps.
Wipe the suction path and base Use a damp cloth to clear lint and foam from the intake.
Clean the 2-in-1 Pet Upholstery Tool Detach, open the gate, and rinse the screen. Let water run through until clear.
Wipe the exterior and cord Keep it clean so grime does not migrate inside.
Air-dry all parts Stand parts upright so water drains away from seals.

I learned this routine while teaching new techs how to clean bissell revolution pet pro in busy pet homes. It stops smells and keeps suction high.

Deep clean your machine monthly

A monthly deep clean clears hidden buildup. It also protects seals and gears.

Remove and wash removable parts Take off the front nozzle, brush roll cover, and both tanks.
Remove brush rolls on models with EZ Clean covers Lift them out. Rinse the rolls and end caps. Spin them in your hands to push out grit.
Clean the suction channel and edge bristles Scrub with a soft brush. Pet hair packs tight here.
Detach and rinse the foot nozzle Rinse until water runs clear through the full width.
Detail the CleanShot area Wipe the orifice gently. Do not poke sharp tools into the jet.
Inspect gaskets and O-rings Look for nicks, warping, or soap crust. Replace if torn.

If you follow these steps, you have already done most of how to clean bissell revolution pet pro like a pro. The machine will run quieter and dry carpets faster.

Clean and deodorize the tanks and filters

Tanks hold residue that can smell. Clean them right so odors do not return.

Clean water tank Rinse with warm water. If film remains, add a drop of dish soap, swish, rinse well.
Dirty water tank Remove the lid, float, and screen. Wash each piece. Rinse until no suds remain.
Lids, seals, and seats Use a brush on grooves. Soap crust here causes air leaks.
Deodorize parts only, not the machine Mix 1 teaspoon white vinegar in a quart of water. Rinse tank parts, then rinse again with plain water. Do not put vinegar in the solution tank during cleaning jobs.

A clear, tight seal is vital to suction. Many “no suction” calls from clients who ask how to clean bissell revolution pet pro end up being a dirty or mis-seated lid.

Clear hair, clogs, and odor-causing gunk

Hair and lint hide in corners. They choke airflow and trap smells.

Check the nozzle edges Hair strings nest at both ends. Pull them out.
Inspect the suction intake Use a flashlight. Remove fuzz with tweezers.
Look at the float stack in the dirty tank If stuck up, suction drops. Rinse and tap it free.
Flush the upholstery tool and hose ends Run warm water through until clear.

If you keep asking how to clean bissell revolution pet pro for odor, target these spots. Hair plus detergent equals a sour film. Clear it, and the smell fades.

Drying and reassembly checklist

Water left inside grows mildew and can trip sensors. Dry parts well.

Stand tanks open-side down on a rack Drain for at least 30 minutes.
Air-dry brush rolls until fully dry Roll them on a towel. Do not reinstall wet.
Wipe gaskets and seats Dry contact surfaces to ensure a tight seal.
Click parts back firmly Seat the nozzle, then the brush cover, until both sides snap.
Mount tanks with a solid click Test the trigger and suction on a dry pass.

I learned to let parts sit overnight in humid rooms. It is the quiet secret in how to clean bissell revolution pet pro without musty smells.

Maintenance schedule and best practices

A simple schedule keeps your BISSELL strong.

After each use Rinse tanks, nozzle, brush cover, and tool. Remove hair. Air-dry.
Monthly Deep clean as shown above. Inspect seals.
Quarterly Check for wear on brush rolls and end caps. Replace if bristles are mashed.
Always use BISSELL-approved formulas in the solution tank Using other mixes can foam too much or harm seals.

This plan locks in the results of how to clean bissell revolution pet pro. It also protects your warranty and your carpets.

Troubleshooting after a clean

If something feels off, run these quick checks.

Low or no suction Reseat the dirty tank. Make sure the lid is tight. Confirm the front nozzle is fully locked on both sides.
Leaking Check that gaskets lie flat. Inspect the clean tank cap and rubber insert.
Brushes not turning Remove debris at the ends. Ensure the brush cover is snapped down. If the belt is broken, contact service.
Excess foam Use less formula and more water next time. Empty the dirty tank sooner.

I see most issues after people rush reassembly. If you remember how to clean bissell revolution pet pro includes “click everything in,” you will avoid 80% of post-clean hiccups.

Safe cleaners to use (and what to avoid)

Use the right fluids in the right place.

In the solution tank Use only BISSELL carpet formulas. They are low-foam and safe for pumps and seals.
For washing parts Use warm water with a drop of mild dish soap. Rinse well.
Avoid in the machine Vinegar, bleach, boiling water, essential oils, and solvent cleaners. They can corrode parts, strip seals, or void your warranty.
On stains Pretreat with the CleanShot and BISSELL-approved spot cleaners.

These rules match guidance from user manuals and service training. They also align with the best results I see while teaching how to clean bissell revolution pet pro for long-term care.

Storage tips for longer life

Store it dry. Store it safe.

Keep it in a dry, cool area Humidity invites mildew.
Never store with water in tanks Water can sour and leak.
Protect from freezing Residual water can crack lines if frozen.
Wrap the cord loosely Tight wraps strain the plug and jacket.

Follow these habits and you will not need to relearn how to clean bissell revolution pet pro before every job.

Frequently Asked Questions of how to clean bissell revolution pet pro

How often should I clean the nozzle and brush cover?

Rinse them after each use. This prevents clogs and keeps suction strong.

Can I put vinegar in the solution tank?

No. Do not run vinegar through the machine. Use only BISSELL formulas in the clean tank.

What if my dirty tank lid keeps popping up?

Check that the gasket is clean and seated. Press until you hear a firm click on both sides.

How do I stop wet pet hair from clogging the intake?

Remove hair from the brush rolls after every job. Rinse the nozzle edges and the suction channel.

Why does my machine smell musty after storage?

Parts were likely stored damp. Rinse, clean, and air-dry fully. Then run a water-only pass to freshen lines.

Do I need to replace brush rolls?

Yes, when bristles are crushed or frayed. Fresh rolls improve agitation and dry time.

What water temperature should I use?

Use warm tap water, not hot. Very hot water can warp plastic and seals.

Conclusion

You now have a clear, proven plan to keep your BISSELL Revolution Pet Pro clean, odor-free, and powerful. Unplug, rinse the key parts, clear hair, dry well, and reassemble with care. Do a quick clean after every job, and a deeper clean each month.

Start this routine today. Your carpets will dry faster, your home will smell fresher, and your machine will last longer. If this guide helped, share it with a fellow pet parent, subscribe for more home care tips, or leave a comment with your own pro tricks.